Since 2005, 16 Years Fire Alarm and Suppression System Manufacturer&Whole Solution Designer
We supply whole fire alarm and suppression system include conventional fire alarm system, addressable fire alarm system, emergency light system, FM200 gas suppression system, fire pump, fire hose reel and cabinet.
  • Home
  • Products
    ASENWARE Fire Alarm Control System are intelligent system which are designed to make it suitable for most of applications. It’s user friendly functionality makes it suitable to program and configure the devices. 7 ” touchscreen display gives the information for fire alarm, trouble , supervisory and other related information all the
    time.This system fully complied with the requirement of EN 54-2 and EN 54-4.
    ASENWARE Fire Pump Series provide fire departments or private users with the ability to pump from any water source.
    The AW-CFP2166 series conventional fire alarm panel is designed based on EN54 part 24 standard. 
    ASENWARE Centralized Monitoring Emergency Luminaire System is designed for managing, monitoring and controlling emergency lights automatically. 
    Asenware FP300 series is a LPCB addressable fire alarm system with one loop of 324 addressable points, comply with EN 54 standard.
    ASENWARE fire fighting telephone system is the special communication equipment for fire fighting
    ASENWARE Heat Detector is photo-electronic detector using a state-of-the-art optical sensing chamber. 
  • Project
  • Newsroom
  • About Us
  • Contact
  • Technical RFQ
LPCB approved conventional fir...
Home > Products > LPCB approved conventional fire alarm control system
4 Zone Fire Alarm Control Panel AW-CFP2166-4-8
The AW-CFP2166 series conventional fire alarm panel is designed based on EN54 part 2&4 standard. And it is the central part of conventional fire alarm system, designed for applications requiring smoke...


  • The AW-CFP2166 series conventional fire alarm panel is designed based on EN54 part 2&4 standard. And it is the central part of conventional fire alarm system, designed for applications requiring smoke detector, bell, manual pull stations, and sprinkler supervision. Each zone can be disabled by a button. The basic unit offers 1 to 8 zones of initiation, up to 16 zones for larger applications.

    Main indication on main board
    1.1Fire alarm indication
    At the top area of the panel is the main display. When enter to fire alarm, the red FIRE LED lights. If the outputs:
    Sounder/ Fire protection/ Fire routing did not disabled or have any faults, red ACTIVE LED light.
    1.2Fault display on main board
    Any fault occurs, General Fault indicator lights.
    On the panel, main display area has 4 outputs: Sounder/ Fire protection/ Fire routing/ Fault routing, if all being wet mode and did not disabled, any fault indicates on the panel. Faults fall into short and open.
    On the left, other faults include mains fault/ battery fault/ earth fault/ fuse fault/ system fault.
    Mains fault: there is no mains power comes to panel. Pull mains plug up, check if wires connect hard. Or fuse is break on the EMI board. Of course, premise your lamp is lighting.
    Battery fault: there is no power comes from batteries. Check the battery switch on, if wires connected well. Of course, premise you have got 2 batteries inside. If all these above are ok, batteries are too old to supply power, change them.
    Earth fault: there are some points on PCBs contact to enclosure. Insure wires connected clearness.
    Fuse fault: the fuse on power board broken. Get it out and put another one inside.
    System fault: open the door, check if every zonal board has a green LED flashing organized. Or if your 4 bits DIP switches are dialed correctly.
    1.3Disablement indication
    The 4 outputs, if anyone disabled, corresponding “disable” lights and “General Disable” lights.
    1.4Indication of operation
    Except 4 outputs, we have another 4 buttons: Test/ Reset/ Evacuate/ Silence, when touch off, the LED belongs to lights and trigger corresponding outputs.
  • Specification
    1. It is modularized design, the panel can expend from 1 zone to 32 zones easily.
    2. It has 2 level control mode by a lock
    3. It has 24VDC and 5VDC power supply output.
    4. It has FIRE and FAULT signal output.
    5. It has 2 general sounders output.
    6. Each zone has 1 circuit detectors input
    7. Each zone can be disable by a button.
    8. It has RESET button to reset the panel.
    9. It has SILENCE button to stop BUZZER and SOUNDERS.
    10. It has EVACUATE button to start a manual fire alarm immediately.
    11. It has battery low protection function, when battery voltage lower than 21VDC
    battery will be cut off automatically until the mains power is on.
    12. It has an optional GSM module for fire alarm by SMS
     

  • AC INPUT
     
    220VAC 50HZ
    +10%
        -15%
    DC OUTPUT 24VDC typical
    Voltage for MCU 5V for power board MCU, 3.3V for others
    Current at 24VDC from PSE 450mA standby current
    Maximum current from PSE 2A except batteries charge
    Batteries current 1.85A maximum, current limited
     
    Auxiliary output
    24VDC +/- 10%, 100 mA max,
    current limited, monitored
     
    Batteries
    2*12V/ 2.3Ah sealed lead acid gel,
    self-regulated
      2*12V/ 7Ah if needed
    Battery replace Resistance 2Ω±10% if needed
    Battery low-voltage protection 22.2V
    Detectors connection allowed each zone 20 (except MCPs)
    Zone alarm current 6mA minimum/ 27mA maximum
    Sounder output 2*0.75A maximum
    Fire protection 100mA maximum
    Fire routing 100mA maximum
    Fault routing 100mA maximum
    Communication protocol 2 wires RS485 bus system
    Relay contacts rating Dry contacts (NO/NC) 1A @24VDC
    EOL resistor for zone 6.8K 1W
    EOL resistor for outputs 6.8K 1W
    Fuse on power board 3A/ 250V glass tube fuse 20mm
    Fuse on EMI board 1A/ 250V glass tube fuse 20mm
     
    Environmental
    Class A temperature range: -5 to 40°C (23~104°F)
    Humidity: 5 to 95% RH, non-condensing
     
    Terminal blocks rating
    All terminals rated for 12 to18 AWG
    (0.75 to 2.5 mm2)