Since 2005, Fire Alarm System And Fire Suppression System Manufacturer&Whole Solution Provider
We supply whole fire alarm and suppression system include conventional fire alarm system, addressable fire alarm system, emergency light system, FM200 gas suppression system, fire pump, fire hose reel and cabinet.
  • Home
  • Products
    Fire alarm system plays an important part of the fire and life safety of building and its occupants. Fire alarm system main function is to detect a fire at a sufficiently early stage so that the people who are at risk can made safely either by escaping as fast as possible or extinguishing the fire that can also reduce or prevent the property damage. Therefore, a reliability and functionality of fire alarm system as a whole is very important. 

    The following are the different types of the Fire Alarm System:

    1. Conventional fire alarm system

    a. Conventional fire alarm system uses physical cabling to connect several detectors and call points. Conventional fire alarm system has no way to identify immediately the exact location of the fire, but can be arranged in “Zones” to easily identify the location of the cause of the alarm. Its devices are cheaper but will consume more cable wires compare to addressable, since each device will be connected to the control panel by its own cable wire. This system are mainly used specially in smaller property.
    conventional fire alarm system Wiring diagram 

    2. Addressable fire alarm system

    a. Addressable fire alarm system has the same detection principle, except that each detector can be given a set address that can help to identify the exact location of the detector that initiated the alarm, that can be seen in the fire alarm control panel. Addressable fire alarm system saves a lot of wire compare to conventional system, since the devices can share one cable wires up to the last device. Both ends of the wire is loop connected to the fire alarm control panel. This system are very suitable for large and high buildings, since they are able to pinpoint exactly which devices are triggering the alarm.
    addressable fire alarm system Wiring diagram

    3. Wireless fire alarm system

    a. Wireless fire alarm system, is hassle-free to install compare to conventional and addressable since it does not use any conduit and cable wires. However, even though you saved a lot of money in material and labor cost, the hardware and programming are higher than the wired systems. The devices are battery powered and can be placed anywhere and can be easily relocate if needed.
    wireless fire alarm system

    Fire Alarm System Components 

    The main component of fire alarm system are the following:
    1. Fire Alarm Control Panel
    Fire Alarm Control Panel is the brain or central hub of a fire alarm system. It displays the location and status of the alarm devices, and it gives precise location of the device that cause the alarm.
    fire alarm control panel
    2. Fire Alarm Initiating Devices
    Fire Alarm Initiating Devices are the devices that detects signs of fire and triggers the alarm. They are connected to the fire alarm system control panel. Initiating devices includes smoke detectors, heat detectors, flame detectors, manual pull station and fire sprinkler water flow switch.
    Fire Alarm Initiating Devices
    3. Fire Notification Devices
    Fire Notification Devices are the audible and visual devices in fire alarm system, it includes fire alarm horn, speaker and bell. Its main function is to alert people at risk in the event of a fire, that is why it is considered as the most important components of fire alarm system.
    Fire Notification Devices
    4. Primary Power Supply
    Primary power supply is typically supplied by the local utility, and also from generators that are located in remote areas wherein the electrical grid is not available. 
    5. Backup Power Supply
    Backup power supply commonly supplied by batteries and stored internally or adjacent to main fire alarm control panel or can be also from generator. It must also provide a 24 hours of power supply to control panel in case of power shortage.

    How Fire Alarm System Works? 

    In an event of a fire emergency, the fire alarm system main role is to detect fire and to alert people at risk inside the building and emergency response team to control the situation as fast as possible. Fire alarm system key functions is to detect (by the use of smoke detectors, heat detectors, flame detectors, etc.) , alert (by the use alarm horn, speaker, and bell), and monitor (control panel). 

    Fire Alarm System Maintenance 

    A functioning and well-maintained fire alarm devices can help reduce injuries, save lives and properties. The fire safety systems inspection, routine maintenance, and testing will help one in keeping in compliance with the local/state fire inspectors and also their insurance carrier. To keep the best condition of the fire alarm devices, it is advisable to keep a scheduled maintenance and check the following: 
    1. Checking of physical appearance of the fire alarm devices
    2. Smoke Detectors should be cleaned & tested for sensitivity levels (addressable type)
    3. Fire alarm control panel should be tested for all alarm, trouble, supervisory, reset & silence function
    4. Checking of the devices power supply
    5. Checking/ replacement of batteries
    6. Checking/ removal of any obstruction on the devices that may cause false alarm or malfunctioning
    7. Checking if the alarm is audible
    8. Devices must be replaced when exceeded 10 years from the manufactured date


    ASENWARE Centralized Monitoring Emergency Luminaire System is designed for managing, monitoring and controlling emergency lights automatically. 
    ASENWARE Fire Pump Series provide fire departments or private users with the ability to pump from any water source.

    At ASENWARE, you can choose the best quality of fire fighting equipment like  extinguisher, hose reels, fire monitors, nozzles and hose pipes.
  • Project
  • Newsroom
  • About Us
  • Contact
  • Technical FAQ
Home > Newsroom
Horn Strobe Features and Installation Guide
The horn strobe is a fire alarm device in the industrial fire alarm system. It is an alarm signal device that sends out warning signals to people through alarm sounds and flashing lights. It is set up to meet the requirements of customers for alarm loudness and installation location.
The horn strobe can be applied in iron and steel metallurgy, telecommunication towers, hoisting machinery, construction machinery, ports, transportation, wind-power generation, ocean-going vessels, and other industries.
The horn strobe is suitable for installation in public places. When there is an accident like a fire, it can sound alarms and flash flashing lights to remind people of the dangerous situations.
The horn strobe can also be applied in hazardous places. For example, the explosion-proof horn strobe is suitable for IIC T6 explosive gas environments, and it can also be used outdoors. When an accident or fire occurs in the production area, the fire alarm control panel will send a control signal to the horn strobe to activate it, and the horn strobe will therefore give alarm sounds and flashing light to warn people. The horn strobe can also be used together with the manual call point.
Horn Strobe

Horn Strobe Features

1.It flashes brightly and the alarm sound is loud.
2.It is small and lightweight, easy and convenient to install.
3.It is durable, reliable and stable when working, and has low power consumption and long using life.
4.Its volume is high and therefore is easy to transmit the alarm sounds over long distances.

Horn Strobe Applications

1.The horn strobe is used for sound and flashing alarms when there is an accident and is suitable for places with low visibility or smoke.
2.The horn strobe can be used in fire alarm control systems, security monitoring alarm systems, and other fire alarm systems. It only needs to connect the power to work.
3.The horn strobe can be connected to the coded / analog fire alarm control system through the control module.
4.The horn strobe can be connected to the distributed intelligent automatic fire alarm control system through the intelligent control module.
5.The horn strobe can also be connected to the gas extinguishing fire alarm control system.

Horn Strobe Installation Requirement

1.There should be horn strobes in each fire compartment, and they should be installed at the exits of the corridor near the stairs on each floor.
2.In a protected area with multiple fire compartments, it is suggestible to choose a horn strobe with voice prompts, and the voice should be synchronized.
3.When installing more than one horn strobe in the same building, it should be able to turn on and turn off all horn strobes at the same time.

Horn Strobe Installation Notes

1.The probe of the horn strobe is mainly the detection element of the contact combustion type gas sensor. It is composed of aluminum oxide and adhesive coated on a platinum wire coil, and its outer surface is attached with rare metals like platinum and palladium. Therefore, you must be careful when installing the horn strobe, avoiding breaking the probe.
2.The installation height of the horn strobe should be above 1.8m, which will be convenient for the maintenance personnel to do daily maintenance jobs.
3.The horn strobe is a safety instrument with sound and light functions. It should be installed in a place where the staff can easily see and hear it, and therefore can solve potential safety problems in time.
4.There should be no devices that will have strong electromagnetic fields, like high-power motors or transformers, around the horn strobes, in case they will affect their work.